You’ll get a robust, highly adjustable STRG fish finder mount with an 11.4" articulated arm and three 360° pivots, built from powder-coated marine-grade aluminum with stainless fasteners for good saltwater resistance. The rectangular plate fits Garmin, Lowrance and Humminbird patterns and supports clamp or screw installations on kayaks and boats. It’s heavier and pricier than minimal mounts but offers superior positioning and durability; keep going to see installation tips, compatibility details, and maintenance advice.
Some Key Takeaways
- Robust 11.4" articulated arm with three 360° pivots offers extensive positioning for boats and kayaks.
- Powder-coated marine-grade aluminum and stainless hardware deliver strong corrosion resistance for saltwater use.
- Rectangular plate with multiple pre-drilled patterns fits Garmin, Lowrance, Humminbird, and similar units.
- Clamp or screw mounting options suit hulls, rails, and kayak installations; route cables along the arm for neat setup.
- Slightly heavier and pricier than minimalist mounts but provides superior durability and long-term value.
Quick Verdict : Who Should Buy the STRG Fish Finder Mount
If you need a robust, highly adjustable mount for a wide range of fishfinders and chartplotters, the STRG Fish Finder Mount is a solid choice. You’ll appreciate its 11.4" arm, three 360° pivots and rectangular plate with multiple hole patterns. Kayak anglers get clamp or screw options to maintain freedom of placement; small-boat users gain shock‑resistant stability. Compatibility spans major Garmin, Lowrance and Humminbird units, so you won’t be tied to one brand. Budget buyers find value in durable, corrosion‑resistant construction that reduces replacement frequency. Choose this mount when adjustability, broad compatibility and long service life matter. It’s especially helpful for kayak anglers who need mounts tailored to their craft and skill level.
What’s Included, Materials, and Corrosion Resistance You Can Expect
While unpacking you'll find a single Strg Fish Finder Swing Mount (rectangular plate with an 11.4" articulated arm) and the stainless-steel hardware required for typical clamp or screw installations, and the kit is deliberately minimal to let you choose clamps or fasteners appropriate for your boat or kayak. The mount uses powder-coated marine-grade aluminum and stainless fasteners; material sourcing targets saltwater durability. Expect corrosion resistance, heat/cold tolerance, and shock resilience for open-water use. You’ll perform basic mount maintenance: rinse with fresh water, inspect fasteners, and apply corrosion inhibitor periodically to preserve finish and function while maximizing installation freedom. For paddlers outfitting small craft, consider a dedicated rope bag to keep your mounting hardware and lines organized.
Compatibility and Mounting Options for Popular Fishfinders and Kayaks
Because the Strg Fish Finder Mount uses a rectangular plate with multiple pre-drilled hole patterns and an 11.4" articulated arm, you'll find it physically compatible with most mainstream fishfinders and chartplotters from Garmin, Lowrance, Humminbird, and others listed in the product specs. You can expect reliable device compatibility across ECHOMAP, GPSMAP, HDS, Hook/Striker series and similar units. Kayak integration supports clamp options or direct-screw mounting to hull or accessory rails. Three pivot points and the swing arm deliver mount stability under motion and shock. Materials and fastener choices maintain corrosion resistance for unrestricted, freedom-minded deployment. This mount is a great choice for kayak enthusiasts looking for portable fish finder solutions.
Installation Walkthrough and Real-World Adjustment Tips
When you start the installation, lay out the mount, hardware, and your fishfinder so you can confirm hole alignment and clamp or screw choices before drilling or tightening. Position the rectangular plate, verify mount alignment with device holes, and choose clamp or screw installation based on hull material. Use the 11.4" arm and three pivot points to set reach and sightlines; tighten pivots incrementally to preserve range. Route power and transducer leads along the arm, secure with zip ties or clips for clean cable management, and test full rotation and swing under load. Recheck fasteners after initial outings. Consider keeping an emergency blanket or similar safety essential on board in case of unexpected cold exposure or capsize.
Pros, Cons, and Final Buying Recommendation
After verifying alignment, tightening pivots incrementally, and routing cables as described, you’ll be in a good position to assess strengths and weaknesses objectively. You get robust corrosion-resistant aluminum, three 360° pivots, and broad device compatibility that give you freedom to position equipment precisely. Cons: added weight and a higher upfront cost versus minimal mounts; check price comparison for similar mounts. Considerations: minimal impact on battery life since mount is passive; confirm warranty terms and reach out to customer support for registration and claims. Final recommendation: choose this mount if you prioritize durability, adjustability, and long-term reliability. For kayak setups, consider adding essential gear like a power pole and anchor trolley to improve stability and positioning on the water.
Some Questions Answered
Does It Include a Lifetime Warranty?
No — it doesn’t include a lifetime warranty. You’ll need to check the manufacturer for warranty details; the product listing states warranty information is available from Strg but doesn’t promise lifetime coverage. Expect coverage limits to specify duration, corrosion exclusions, and proof-of-purchase requirements. You can contact Strg for exact terms, claim procedures, and whether extended or replacement warranties are offered to preserve your freedom to choose repair or replacement.
Can It Support Dual Fishfinder Setups?
Yes — you can. You’ll mount two units using the rectangular plate’s multiple pre-drilled holes and the 11.4" arm’s three 360° pivots to position mirrored displays and route dual transducers. Clamp or screw installation secures both devices; materials resist corrosion and shock. You’ll adjust each head independently for clear sightlines, keeping both transducer cables tidy. Check weight and footprint limits for very large/chartplotter combos.
Is Tool-Free Adjustment Possible on the Arm?
Yes — you can perform tool free adjustments on the arm using the quick release-style pivot lock. You’ll release the pivot lock and reposition the arm hands free, then re-engage the quick release to secure it. The three 360-degree pivot points offer rapid, repeatable positioning without tools, giving you freedom to reorient displays quickly while underway. The mechanism is robust and designed for marine conditions, balancing ease and secure fixation.
Will It Fit on Canoe Gunwales?
Yes — it’ll fit canoe gunwales if your gunnel width and mounting approach match. You’ll verify canoe compatibility by measuring gunnel width and confirming clamp or screw clearance. The 11.4" arm and rectangular plate accept clamping or through-bolting; three 360° pivots let you position without obstruction. For thin or rounded gunwales use padded clamps or backing plates to distribute load and prevent crushing or hardware pull-through.
Are Replacement Plates Available Separately?
Yes — replacement plates are available separately through the manufacturer and select retailers. You can order OEM replacement plates or source third party compatibility plates that match the rectangular pre-drilled pattern. You’ll want to verify hole spacing and material specs before buying. Keep in mind corrosion-resistant construction and mounting tolerance to maintain durability. If you need exact part numbers or vendor links, you can request them and you’ll get targeted options.
